Quick Reference Guide for the Napco 1016e

Quick Reference Guide for the Napco 1016e

To set alarm: Close all doors and wait for system to display (system ready). Once it's ready, enter your code. The Red "armed" light should come on. You have 45 seconds to leave through your predetermined exit/entry door, after which the system is fully armed.

To disarm the system: Enter your code. To shut off the siren for a fire alarm activation: The fire alarm circuit is always active, regardless of whether the burglar alarm is on or not. To shut the siren off when the fire circuit trips, just enter your code until the siren stops.

To reset the alarm after a burglary or fire trip: Press and hold the number 9 key until it beeps. (Note: If you still have smoke in the area when you reset the system, the detectors may trip again. Please ensure that you have cleared any smoke before resetting the detectors.)

To bypass a zone: Before arming the system press the B key followed by the zone number you wish to bypass 01-14. (the B key also serves as the 0 key) The bypass light should come on. To check which zones you've bypassed, just hold the number 2 button (display bypass) down and it will scroll through which zones you've bypassed.

Group bypass: If your system is programmed for group bypass, you can bypass all the devices in that group by pressing the B key twice prior to arming your system.

Note: If you get a "P" on the keypad, just enter your code again. This will occur if you try to arm the system with a door open or someone in front of a motion detector. This means problem and you need to take care of that zone before you can arm.

Panic Button: Press * and # simultaneously. This will cause the sirens to sound and automatically dispatch the police. We will not call to verify a passcode. If you've made an error, call central station at 305-238-0800.

Ambush: If you are forced to shut off the system, begin your code with your emergency digits followed by your normal code. (If you do not know your emergency digits, just give us a call) This will disarm the system while sending a silent signal that you are under duress. We will not make a call to verify a passcode.

Door Chime: Pressing and holding the number 5 button just toggles the door chime on and off. Doors that have been pre-selected to chime (usually the entry doors) will cause the keypad to chime for 2 seconds when opened. The only way to verify if it is on or off is to test it by opening or closing the door.

To change the codes (can also be programmed remotely by One Source Security).

1. Hold down number 8 until it beeps

2. Enter your program code. Call if you are not sure of your code number.

3. Select which code you're going to program by pressing the B key followed by the user # 10-15.

4. Enter the actual code you want to use (2-5 digits - no zeros).

5. To enter another code repeat steps 3 and 4.

6. To exit the program mode press the B (or 0) key three times.

Example, programming user number five's code as 1234: 1. Hold down number 8 until it beeps. 2. Enter your program code. 3. Press B 05. 4. Enter 1234. 5. Exit the program mode - press the B (or 0) key three times. To delete a user code and leave that space empty: Perform steps 1,2,3,5 and 6 above.

Troubles:

1. All three lights on keypad are flashing. In the left window a 1 is flashing = Your A.C. power is off to the panel

2. All three lights on keypad are flashing. In the left window a 2 is flashing = You have a low battery on your system. If you recently lost power and it has now come back on, the battery should recharge itself within a few hours.

3. All three lights on keypad are flashing. In the left window a 3 is flashing = Your system attempted to communicate with central station and failed. You should call for service to have your system communications checked.

Quick Reference Guide for the Napco 1008e

To set alarm: Close all doors and wait for system to display (system ready). Once it's ready, enter your code. The Red "armed" light should come. You have 45 seconds to leave through your predetermined exit/entry door, after which the system is fully armed.

To bypass a zone: Before arming the system press the B key followed by the zone number you wish to bypass 1-8. The bypass light should come on. To check which zones you've bypassed, just hold the number 2 button (display bypass) down and it will scroll through which zones you've bypassed.